Samsung I9300 direct emmc boot repair issue Solved How To Guide 100% Tested

Today i have come one Samsung i9300 which is automatically dead
i will try to repair boot with Mmc method not work than i will try TP mmc method its also not work
After that try with direct emmc method connection OK
But just hang on any Oparaction not erased not write etc ...
Here is the error log
Download this:
i9300_atf_emmc.rar

Code:

======================================================
======================================================
       eMMC Test Point Connection Module             
======================================================
==========================================Code:============
                                                      
1. DO NOT USE THE PHONE"S BATTERY                     
2. Connect the Soldered TP Connections to ATF Box     
3. Disconnect the USB Cable and Wait until the        
   the ATF Software will tell you to Connect the USB. 
                                                      

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V
1.45-1.50V

CID : 15010056545530304DF159A77732
CSD : D02701320F5903FFF6DBFFFF8E40406D

eMMC Boot Information
Revision 1.6 (for MMC v4.5)
BOOT PARTITION     : BOOT PARTITION 1
PARTITION ACCESS   : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT  : DISABLED
BOOT MODE          : x4 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH    : ENABLED
eMMC FirmW UPDATE  : DISABLED
EMMC CACHE SIZE    : 0 KB
SUPER PAGE SIZE    : 3584 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE     : 15758000128 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 128 KB


eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type    : Embedded BGA
Application ID : 00
Product Name   : VTU00M
Product Rev    : 15.1
Product SN     : 59A77732
Manufactured   : January 2012

Card Specific Data
CSD_STRUCTURE     : Extended
SPEC_VERS         : Version 4.1/4.2/4.3
TAAC              : 13 ns
TRANS_SPEED       : 4000000 KHz
READ_BL_LEN       : 512 Bytes
C_SIZE            : HIGH CAPACITY
WP_GRP_ENABLE     : YES
WRITE_BL_LEN      : 512 Bytes
CONTENT_PROT_APP  : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
15010056545530304DF159A77732_932DD6C7.ext_csd
Backup Directory:
G:\All Software Box\A T F\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\


Task Selected: Normal Factory Erase
======================================================
For eMMC Revision 1.2 (for MMC v4.2) and LOWER
--> This will ERASE USER AREA, BOOT1, BOOT2, and RPMB
For eMMC Revision 1.3 (for MMC v4.3) and HIGHER
--> This will ONLY ERASE USER AREA
======================================================
This eMMC is: Revision 1.6 (for MMC v4.5)

Factory Erasing Supported FLASH AREA...

here is my connection pic





Atf team supporters Pls kindly tell me Where I'm doing wrong